Crankshaft J&G 2% special by BGM Pro
Shipping to:
Währung:
Language: Deutsch English French Swedish Schweiz
0 Products | 0,00 EUR |  CHECKOUT
SELECT YOUR VEHICLE  ❯❯
we ship worldwide
shipping to  US  from 34,40 EUR
256 bit ssl-encryption • PCI DSS compliant • express shipping
PARTS AND ACCESSORIES
Shop by Brand

Crankshaft -J&G 2% special by BGM Pro (rotary valve) 60mm stroke, 125mm connecting rod, piston pin=Ø16mm- Vespa PX80-150 - for adaptation of a PX200 cylinder by means of adapter plate

Item No:
50340
192,44 EUR
prices incl. 0% sales tax, free shipping in GER
gross weight: 2,20 kg

Crankshaft -BGM Pro Touring (rotary valve) 60mm stroke, 125mm connecting rod, piston pin Ø16mm

Vespa PX80, PX125, PX150, Cosa125, Cosa150, LML Star/Stella 125/150 2-stroke

Special crankshaft with extra long conrod e.g. for Pinasco 206cc, Barone 230, Simonini etc.
This
crankshaft was equipped with an extra long connecting rod (125mm instead of 105mm). This also has a large upper connecting rod bearing, suitable for piston pins with Ø16mm instead of Ø15mm (can be used with our conversion connecting rod bearing but also with Ø15mm piston pins).
Perfect crankshaft for special engine conversions where a long connecting rod is needed. Due to the much better connecting rod ratio (0.24 instead of 0.28) engines with this shaft are also very smooth running.
  • HUB: 60mm

CONNECTING
  • LENGTH

  • :
  • 125mm

  • INLET CONTROL: Rotary slide (cheek width like PX125/150)

PISTON PISTON
  • : Ø16mm (Ø15mm with conversion piston pin bearing, see accessories)


MATERIAL
The bgm PRO Touring crankshafts are forged

.

The material is denser, thus dissipates heat better and is more resistant to distortion. In addition to the crank webs, the connecting rod is also forged.

BEARING
The lower connecting rod bearing is lubricated via two large lubrication slots and a total of four additional pockets on the side
.
The SSC race bearing and side thrust washers provide solid bearing support. The upper connecting rod bearing is lubricated via two lubrication holes. The INA piston pin bearing is included with the crankshaft.


INLET ANGLE

The bgm PRO Touring shaft has a much better inlet layout compared to many other racing shafts


.

For tuning cylinders, the standard shaft with its very short intake time cannot keep up. The bgm PRO shaft, on the other hand, closes on a PX engine case about 58° after top dead center (depending on the engine case, this varies from the factory). The engine can be tuned well with these timing angles. TIP: If the intake is machined so that the crankshaft clears the intake slot earlier, additional power can be gained. A good value has been found to be approx. 120° from TDC.

RELEASE
The crankshaft design of the PX engines is based on that of the first 125cm³ engines from 1960 with approx. 5 HP power. Unfortunately Piaggio never really changed this design in the later displacement extensions . Thus, the load capacity of the crankshaft with the standard 200cc models with 12HP is mathematically already exhausted. The crank webs are very narrow and have very little overlap (web material that, seen in diameter, is available above the lower crankpin). This means that neither a particularly high interference fit nor a large crankpin can be used, as would be necessary (for the performance of today`s engines).
The BGM PRO Touring crankshafts have a very high material quality and bearing. In addition, the crankpins are glued for maximum torsion resistance. Due to the positive experiences, collected in many thousands of test kilometers of our own daily used engines, we release the BGM PRO Touring crankshafts for engine power up to 25HP. For engines in this power range, we recommend the use of a lightened pole wheel with a maximum weight of 2300gr.

CONCLUSIONThe bottom line is that
the bgm PRO crankshaft offers the highest quality in every component
.
Precision in manufacturing, materials used and especially the precise balancing leave nothing to be desired. This guarantees extremely smooth and vibration-free engine running.

TIP It is
best to order directly the oil seal 24x35x7 from the Gilera Runner with
.
The Wedi seat of the bgm shaft is wider than usual and can therefore be driven with a double-lipped Viton Wedi.













AI-translation







Item No:
50340
EAN/UPC:
4251389128144
Shipping:
2-7 days
Manufacturer:
BGM PRO
gross weight:
2,20 kg
There are no customer reviews yet.

In order to best respond to your inquiry, please provide us with information about your vehicle, such as brand, name, registration date, serial number and model code. These information can be found in your vehicle registration certificate.

Enquiry:
* Your email adress will solely be used for the handling of your contact request. All information on the handling of you personal data can be found in our privacy policy.
Customers who purchased this product also purchased
MY ACCOUNT
eMail:
Password:
 
Zahlarten
INTERNATIONAL
FOLLOW US
facebook vimeo instagram youtube snapchat

geprüfter Shop IT-Recht-Kanzlei Datenschutz Codex Comodo
All prices are including VAT plus Shipping Costs depend on company providing service, price and weight and possible costs for cash on delivery. Catalogue English Sitemap
® All brand names, trademarks and registered trademarks are property of their rightful owners and are used only for description. OEM numbers are for comparison purpose only.
¹ Please note our ">additional terms for partial revocation. ² True for orders including items marked with "Ready for Shipment: 24 Hours", not valid for orders with payment "bank transfer".
© Racing Planet Vertrieb GmbH 2019


* plus shipping